Air Conditioning System Using Vechile Suspension
DOI:
https://doi.org/10.61841/d6q1z112Keywords:
Suspension System, Single Acting Cylinder, Non-Return Valve, Storage Tank, Heat Exchanger.Abstract
In this project, we are collecting air cylinders and storing this energy in the compressor tank as a nonconventional method by simply driving the vehicle. A non-conventional energy system is very essential at this time to our nation. Compressed air production using a vehicle suspensor needs no fuel input power to produce the output of the air. For this project, the conversion of the force energy into air. The control mechanism carries the air cylinder (vehicle suspension), quick exhaust valve, non-return valve, and spring arrangement. Then this compressed air is passed to the heat exchangers. That is used to convert the heated air into cold air. Cold air is passed to the vehicle. The conventional vehicle suspension dissipates the mechanical energy, i.e., potential and kinetic energy. In spring, potential energy is stored and kinetic energy is wasted. The aim of this paper is that this wasted energy is compressed by using a single-acting cylinder in proper arrangement. The main aim of this paper is the compressed air production using vehicle suspension given to the air conditioning system. The pushing power is converted into compressed air energy by proper arrangement. The pneumatic single-acting cylinder is used for this project to compress the air. The output air from the pneumatic cylinder is collected through the quick exhaust valve and non-return valve, and this compressed air is stored inside the storage tank. After this research, we concluded that in a car there is a lot of fuel burned only for working of the A.C. while driving the car. If A.C. will run on another system rather than fuel, then there is lot of fuel saved in car, hence the efficiency of car will also increase
Downloads
References
1] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Virtual instrumentation based process of
agriculture by automation. Middle-East Journal of Scientific Research, 20(12): 2604-2612.
[2] Udayakumar, R., Kaliyamurthie, K.P., & Khanaa, T.K. (2014). Data mining a boon: Predictive system for
university topper women in academia. World Applied Sciences Journal, 29(14): 86-90.
[3] Anbuselvi, S., Rebecca, L.J., Kumar, M.S., & Senthilvelan, T. (2012). GC-MS study of phytochemicals in
black gram using two different organic manures. J Chem Pharm Res., 4, 1246-1250.
[4] Subramanian, A.P., Jaganathan, S.K., Manikandan, A., Pandiaraj, K.N., Gomathi, N., & Supriyanto, E.
(2016). Recent trends in nano-based drug delivery systems for efficient delivery of phytochemicals in
chemotherapy. RSC Advances, 6(54), 48294-48314.
[5] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Partial encryption and partial inference control
based disclosure in effective cost cloud. Middle-East Journal of Scientific Research, 20(12), 2456-2459.
[6] Lingeswaran, K., Prasad Karamcheti, S.S., Gopikrishnan, M., & Ramu, G. (2014). Preparation and
characterization of chemical bath deposited cds thin film for solar cell. Middle-East Journal of Scientific
Research, 20(7), 812-814.
[7] Maruthamani, D., Vadivel, S., Kumaravel, M., Saravanakumar, B., Paul, B., Dhar, S.S., Manikandan, A., &
Ramadoss, G. (2017). Fine cutting edge shaped Bi2O3rods/reduced graphene oxide (RGO) composite for
supercapacitor and visible-light photocatalytic applications. Journal of colloid and interface science, 498,
449-459.
[8] Gopalakrishnan, K., Sundeep Aanand, J., & Udayakumar, R. (2014). Electrical properties of doped
azopolyester. Middle-East Journal of Scientific Research, 20(11). 1402-1412.
[9] Subhashree, A.R., Parameaswari, P.J., Shanthi, B., Revathy, C., & Parijatham, B.O. (2012). The reference
intervals for the haematological parameters in healthy adult population of chennai, southern India. Journal
of Clinical and Diagnostic Research: JCDR, 6(10), 1675-1680.
[10] Niranjan, U., Subramanyam, R.B.V., & Khanaa, V. (2010, September). Developing a web recommendation
system based on closed sequential patterns. In International Conference on Advances in Information and
Communication Technologies, 101, 171-179. Springer, Berlin, Heidelberg.
[11] Slimani, Y., Baykal, A., & Manikandan, A. (2018). Effect of Cr3+ substitution on AC susceptibility of Ba
hexaferrite nanoparticles. Journal of Magnetism and Magnetic Materials, 458, 204-212.
[12] Premkumar, S., Ramu, G., Gunasekaran, S., & Baskar, D. (2014). Solar industrial process heating
associated with thermal energy storage for feed water heating. Middle East Journal of Scientific
Research, 20(11), 1686-1688.
[13] Kumar, S.S., Karrunakaran, C.M., Rao, M.R.K., & Balasubramanian, M.P. (2011). Inhibitory effects of
Indigofera aspalathoides on 20-methylcholanthrene-induced chemical carcinogenesis in rats. Journal of
carcinogenesis, 10.
[14] Beula Devamalar, P.M., Thulasi Bai, V., & Srivatsa, S.K. (2009). Design and architecture of real time webcentric tele health diabetes diagnosis expert system. International Journal of Medical Engineering and
Informatics, 1(3), 307-317.
[15] Ravichandran, A.T., Srinivas, J., Karthick, R., Manikandan, A., & Baykal, A. (2018). Facile combustion
synthesis, structural, morphological, optical and antibacterial studies of Bi1− xAlxFeO3 (0.0≤ x≤ 0.15)
nanoparticles. Ceramics International, 44(11), 13247-13252.
[16] Thovhogi, N., Park, E., Manikandan, E., Maaza, M., & Gurib-Fakim, A. (2016). Physical properties of
CdO nanoparticles synthesized by green chemistry via Hibiscus Sabdariffa flower extract. Journal of Alloys
and Compounds, 655, 314-320.
[17] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Wide area wireless networks-IETF. MiddleEast Journal of Scientific Research, 20(12), 2042-2046.
[18] Sundar Raj, M., Saravanan, T., & Srinivasan, V. (2014). Design of silicon-carbide based cascaded
multilevel inverter. Middle-East Journal of Scientific Research, 20(12), 1785- 1791.
[19] Achudhan, M., Jayakumar M.P. (2014). Mathematical modeling and control of an electrically-heated
catalyst. International Journal of Applied Engineering Research, 9(23), 23013.
[20] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2013). Application of pattern recognition for farsi
license plate recognition. Middle-East Journal of Scientific Research, 18(12), 1768-1774.
[21] Jebaraj, S., Iniyan S. (2006). Renewable energy programmes in India. International Journal of Global
Energy Issues, 26(43528), 232-257.
[22] Sharmila, S., & Jeyanthi Rebecca, L. (2013). Md Saduzzaman., Biodegradation of domestic effluent using
different solvent extracts of Murraya koenigii. J Chem and Pharm Res, 5(2), 279-282.
[23] Asiri, S., Sertkol, M., Guner, S., Gungunes, H., Batoo, K.M., Saleh, T.A., Manikandan A., & Baykal, A.
(2018). Hydrothermal synthesis of CoyZnyMn1-2yFe2O4 nanoferrites: magneto-optical
investigation. Ceramics International, 44(5), 5751-5759.
[24] Rani, A.J., & Mythili, S.V. (2014). Study on total antioxidant status in relation to oxidative stress in type 2
diabetes mellitus. Journal of clinical and diagnostic research: JCDR, 8(3), 108-110.
[25] Karthik, B. (2014). Arulselvi, Noise removal using mixtures of projected gaussian scale mixtures. MiddleEast Journal of Scientific Research, 20(12), 2335-2340.
[26] Karthik, B., Arulselvi, & Selvaraj, A. (2014). Test data compression architecture for low power VLSI
testing. Middle - East Journal of Scientific Research, 20(12), 2331-2334.
[27] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). Privacy conscious screening framework
for frequently moving objects. Middle-East Journal of Scientific Research, 20(8), 1000-1005.
[28] Kaliyamurthie, K.P., Parameswari, D., & Udayakumar, R. (2013). QOS aware privacy preserving location
monitoring in wireless sensor network. Indian Journal of Science and Technology, 6(5), 4648-4652.
[29] Silambarasu, A., Manikandan, A., & Balakrishnan, K. (2017). Room-temperature superparamagnetism and
enhanced photocatalytic activity of magnetically reusable spinel ZnFe 2 O 4 nanocatalysts. Journal of
Superconductivity and Novel Magnetism, 30(9), 2631-2640.
[30] Jasmin, M., Vigneshwaran, T., & Beulah Hemalatha, S. (2015). Design of power aware on chip embedded
memory based FSM encoding in FPGA. International Journal of Applied Engineering Research, 10(2),
4487-4496.
[31] Philomina, S., & Karthik, B. (2014). Wi-Fi energy meter implementation using embedded linux in ARM
9. Middle-East Journal of Scientific Research, 20, 2434-2438.
[32] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). A DFIG based wind generation system
with unbalanced stator and grid condition. Middle-East Journal of Scientific Research, 20(8), 913-917.
[33] Rajakumari, S.B., & Nalini, C. (2014). An efficient data mining dataset preparation using aggregation in
relational database. Indian Journal of Science and Technology, 7, 44-46.
[34] Karthik, B., Kiran Kumar, T.V.U., Vijayaragavan, P., & Bharath Kumaran, E. (2013). Design of a digital
PLL using 0.35 μm CMOS technology. Middle-East Journal of Scientific Research, 18(12), 1803-1806.
[35] Sudhakara, P., Jagadeesh, D., Wang, Y., Prasad, C.V., Devi, A.K., Balakrishnan, G., Kim B.S., & Song, J.I.
(2013). Fabrication of Borassus fruit lignocellulose fiber/PP composites and comparison with jute, sisal and
coir fibers. Carbohydrate polymers, 98(1), 1002-1010.
[36] Kanniga, E., & Sundararajan, M. (2011). Modelling and characterization of DCO using pass transistors.
In Future Intelligent Information Systems, 86(1), 451-457. Springer, Berlin, Heidelberg.
[37] Sachithanandam, P., Meikandaan, T.P., & Srividya, T. Steel framed multi storey residential building
analysis and design. International Journal of Applied Engineering Research, 9(22), 5527-5529.
[38] Kaliyamurthie, K.P., Udayakumar, R., Parameswari, D., & Mugunthan, S.N. (2013). Highly secured online
voting system over network. Indian Journal of Science and Technology, 6(S6), 4831-4836.
[39] Sathyaseelan, B., Manikandan, E., Lakshmanan, V., Baskaran, I., Sivakumar, K., Ladchumananandasivam,
R., Kennedy, J., & Maaza, M. (2016). Structural, optical and morphological properties of post-growth
calcined TiO2 nanopowder for opto-electronic device application: Ex-situ studies. Journal of Alloys and
Compounds, 671, 486-492.
[40] Saravanan, T., Sundar Raj M., & Gopalakrishnan K. (2014). SMES technology, SMES and facts system,
applications, advantages and technical limitations. Middle - East Journal of Scientific Research, 20(11),
1353-1358.
[41] Gomathy, S., Deepa, K.P., Revathi, T., & Visuwasam, L.M.M. (2013). Genre Specific Classification for
Information Search and Multimodal Semantic Indexing for Data Retrieval. The SIJ Transactions on
Advances in Space Research & Earth Exploration, 1(1), 10-15.
[42] Poongodi, R.K., & Sivakumar, T. (2018). Enhanced Adaptive Multimedia Data Forwarding for Privacy
Preservation in Vehicular Ad-Hoc Networks Using Authentication Group Key. Bonfring International
Journal of Software Engineering and Soft Computing, 8(1), 26-30.
[43] Renuga Devi, M., Pavithra, D., & Dharani, K.R. (2014).Isolation Enhancement in Microstrip Patch
Antennas for WiMAX Applications. The SIJ Transactions on Computer Networks & Communication
Engineering (CNCE), 2(2), 1-4.
[44] Ismail, K., & KHALIL, N. H. (2019). Estimation of Reliability of D Flip-Flops Using MC Analysis.
Journal of VLSI Circuits and Systems, 1(1), 10-12.
[45] Pooja, & Vishwakarma, S. (2016). Abnormal Crowd behavior Detection Using Structural Context
Descriptor. Bonfring International Journal of Advances in Image Processing, 6(3), 17-21.
[46] Venkatesh Kumar, S. (2018). Comparative Analyses of Swarm Intelligence Methods for Dimensionality
Reduction in Hyper Spectral Images.Journal of Computational Information Systems, 14(3), 94 - 100.
[47] Dr. Srivastava, S., Srivastava, K., Pandey, A., & Sharma, A. (2014). Data Mining in Telecommunication
Industries. International Journal of Advances in Engineering and Emerging Technology, 5(2), 75-79.
[48] Mohankumar, T. (2014). Area-Efficient and High Speed Carry Select Adder. Excel International Journal of
Technology, Engineering and Management, 1(4), 108-111.
[49] Malathi Ravindran, R., & Dr. Thanamani, A.S. (2015). K-Means Document Clustering using Vector Space
Model. Bonfring International Journal of Data Mining, 5(2), 10-14.
[50] Alborji, B., & Heibari, A.H.K. (2015). The simulation and analysis of the vacancy of 3- phase- 5 levels’
inverter with diodes’ cut topology (DCMLI) and sinusoidal pulses with modulations technique (SPWM).
International Academic Journal of Innovative Research, 2(9), 33-43.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Author
This work is licensed under a Creative Commons Attribution 4.0 International License.
You are free to:
- Share — copy and redistribute the material in any medium or format for any purpose, even commercially.
- Adapt — remix, transform, and build upon the material for any purpose, even commercially.
- The licensor cannot revoke these freedoms as long as you follow the license terms.
Under the following terms:
- Attribution — You must give appropriate credit , provide a link to the license, and indicate if changes were made . You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
- No additional restrictions — You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
Notices:
You do not have to comply with the license for elements of the material in the public domain or where your use is permitted by an applicable exception or limitation .
No warranties are given. The license may not give you all of the permissions necessary for your intended use. For example, other rights such as publicity, privacy, or moral rights may limit how you use the material.
