Hybrid Two Wheeler [HYBYK]
DOI:
https://doi.org/10.61841/ww12aa54Keywords:
Fuel Consumption, Less Polluting, Economic, HYBYK.Abstract
Fuel consumption is one of the most important aspects that has to be noted before selecting any vehicle. Reduced usage of fuel with high efficiency is a characteristic of a good vehicle. With the increase in demand for fossil fuels, the need for a fuel-efficient two-wheeler has increased to a greater extent. Due to aspects such as cost and reliability, alternate fuels cannot replace fossil fuels completely. These efforts are mainly towards achieving a fuel-efficient two-wheeler, 'HYBYK,’ which uses both an IC engine and an electric drive. In a two-wheeler, while traveling a short distance, fuel consumption to power output ratio is comparatively less. Whereas an electric bike cannot travel longer distances but can cover short distances effectively. HYBYK combines these two properties and adds as an advantage. Since HYBYK has both an engine and an electric drive, short distances can be covered with the help of an electric drive and longer distances with a high fuel-to-power output ratio. Also, the system gets considerably charged while running. If fuel gets empty, an electric drive is there to lend a hand. Besides, there is a static solar power module that can be used to charge the battery. Thus, charging the battery becomes almost pollution-free. In a country like India where millions of people flock in traffic and waste fuel, HYBYK would serve better. Thus, with reasons such as reduced fuel consumption, less polluting, and economics, HYBYK would be a promising technology for a global green scenario.
Downloads
References
[1] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Virtual instrumentation based process of
agriculture by automation. Middle-East Journal of Scientific Research, 20(12): 2604-2612.
[2] Udayakumar, R., Kaliyamurthie, K.P., & Khanaa, T.K. (2014). Data mining a boon: Predictive system for
university topper women in academia. World Applied Sciences Journal, 29(14): 86-90.
[3] Anbuselvi, S., Rebecca, L.J., Kumar, M.S., & Senthilvelan, T. (2012). GC-MS study of phytochemicals in
black gram using two different organic manures. J Chem Pharm Res., 4, 1246-1250.
[4] Subramanian, A.P., Jaganathan, S.K., Manikandan, A., Pandiaraj, K.N., Gomathi, N., & Supriyanto, E.
(2016). Recent trends in nano-based drug delivery systems for efficient delivery of phytochemicals in
chemotherapy. RSC Advances, 6(54), 48294-48314.
[5] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Partial encryption and partial inference control
based disclosure in effective cost cloud. Middle-East Journal of Scientific Research, 20(12), 2456-2459.
[6] Lingeswaran, K., Prasad Karamcheti, S.S., Gopikrishnan, M., & Ramu, G. (2014). Preparation and
characterization of chemical bath deposited cds thin film for solar cell. Middle-East Journal of Scientific
Research, 20(7), 812-814.
[7] Maruthamani, D., Vadivel, S., Kumaravel, M., Saravanakumar, B., Paul, B., Dhar, S.S., Manikandan, A., &
Ramadoss, G. (2017). Fine cutting edge shaped Bi2O3rods/reduced graphene oxide (RGO) composite for
supercapacitor and visible-light photocatalytic applications. Journal of colloid and interface science, 498,
449-459.
[8] Gopalakrishnan, K., Sundeep Aanand, J., & Udayakumar, R. (2014). Electrical properties of doped
azopolyester. Middle-East Journal of Scientific Research, 20(11). 1402-1412.
[9] Subhashree, A.R., Parameaswari, P.J., Shanthi, B., Revathy, C., & Parijatham, B.O. (2012). The reference
intervals for the haematological parameters in healthy adult population of chennai, southern India. Journal
of Clinical and Diagnostic Research: JCDR, 6(10), 1675-1680.
[10] Niranjan, U., Subramanyam, R.B.V., & Khanaa, V. (2010, September). Developing a web recommendation
system based on closed sequential patterns. In International Conference on Advances in Information and
Communication Technologies, 101, 171-179. Springer, Berlin, Heidelberg.
[11] Slimani, Y., Baykal, A., & Manikandan, A. (2018). Effect of Cr3+ substitution on AC susceptibility of Ba
hexaferrite nanoparticles. Journal of Magnetism and Magnetic Materials, 458, 204-212.
[12] Premkumar, S., Ramu, G., Gunasekaran, S., & Baskar, D. (2014). Solar industrial process heating associated
with thermal energy storage for feed water heating. Middle East Journal of Scientific Research, 20(11),
1686-1688.
[13] Kumar, S.S., Karrunakaran, C.M., Rao, M.R.K., & Balasubramanian, M.P. (2011). Inhibitory effects of
Indigofera aspalathoides on 20-methylcholanthrene-induced chemical carcinogenesis in rats. Journal of
carcinogenesis, 10.
[14] Beula Devamalar, P.M., Thulasi Bai, V., & Srivatsa, S.K. (2009). Design and architecture of real time webcentric tele health diabetes diagnosis expert system. International Journal of Medical Engineering and
Informatics, 1(3), 307-317.
[15] Ravichandran, A.T., Srinivas, J., Karthick, R., Manikandan, A., & Baykal, A. (2018). Facile combustion
synthesis, structural, morphological, optical and antibacterial studies of Bi1− xAlxFeO3 (0.0≤ x≤ 0.15)
nanoparticles. Ceramics International, 44(11), 13247-13252.
[16] Thovhogi, N., Park, E., Manikandan, E., Maaza, M., & Gurib-Fakim, A. (2016). Physical properties of CdO
nanoparticles synthesized by green chemistry via Hibiscus Sabdariffa flower extract. Journal of Alloys and
Compounds, 655, 314-320.
[17] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Wide area wireless networks-IETF. Middle-East
Journal of Scientific Research, 20(12), 2042-2046.
[18] Sundar Raj, M., Saravanan, T., & Srinivasan, V. (2014). Design of silicon-carbide based cascaded
multilevel inverter. Middle-East Journal of Scientific Research, 20(12), 1785- 1791.
[19] Achudhan, M., Jayakumar M.P. (2014). Mathematical modeling and control of an electrically-heated
catalyst. International Journal of Applied Engineering Research, 9(23), 23013.
[20] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2013). Application of pattern recognition for farsi
license plate recognition. Middle-East Journal of Scientific Research, 18(12), 1768-1774.
[21] Jebaraj, S., Iniyan S. (2006). Renewable energy programmes in India. International Journal of Global
Energy Issues, 26(43528), 232-257.
[22] Sharmila, S., & Jeyanthi Rebecca, L. (2013). Md Saduzzaman., Biodegradation of domestic effluent using
different solvent extracts of Murraya koenigii. J Chem and Pharm Res, 5(2), 279-282.
[23] Asiri, S., Sertkol, M., Guner, S., Gungunes, H., Batoo, K.M., Saleh, T.A., Manikandan A., & Baykal, A.
(2018). Hydrothermal synthesis of CoyZnyMn1-2yFe2O4 nanoferrites: magneto-optical
investigation. Ceramics International, 44(5), 5751-5759.
[24] Rani, A.J., & Mythili, S.V. (2014). Study on total antioxidant status in relation to oxidative stress in type 2
diabetes mellitus. Journal of clinical and diagnostic research: JCDR, 8(3), 108-110.
[25] Karthik, B. (2014). Arulselvi, Noise removal using mixtures of projected gaussian scale mixtures. MiddleEast Journal of Scientific Research, 20(12), 2335-2340.
[26] Karthik, B., Arulselvi, & Selvaraj, A. (2014). Test data compression architecture for low power VLSI
testing. Middle - East Journal of Scientific Research, 20(12), 2331-2334.
[27] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). Privacy conscious screening framework
for frequently moving objects. Middle-East Journal of Scientific Research, 20(8), 1000-1005.
[28] Kaliyamurthie, K.P., Parameswari, D., & Udayakumar, R. (2013). QOS aware privacy preserving location
monitoring in wireless sensor network. Indian Journal of Science and Technology, 6(5), 4648-4652.
[29] Silambarasu, A., Manikandan, A., & Balakrishnan, K. (2017). Room-temperature superparamagnetism and
enhanced photocatalytic activity of magnetically reusable spinel ZnFe 2 O 4 nanocatalysts. Journal of
Superconductivity and Novel Magnetism, 30(9), 2631-2640.
[30] Jasmin, M., Vigneshwaran, T., & Beulah Hemalatha, S. (2015). Design of power aware on chip embedded
memory based FSM encoding in FPGA. International Journal of Applied Engineering Research, 10(2),
4487-4496.
[31] Philomina, S., & Karthik, B. (2014). Wi-Fi energy meter implementation using embedded linux in ARM
9. Middle-East Journal of Scientific Research, 20, 2434-2438.
[32] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). A DFIG based wind generation system
with unbalanced stator and grid condition. Middle-East Journal of Scientific Research, 20(8), 913-917.
[33] Rajakumari, S.B., & Nalini, C. (2014). An efficient data mining dataset preparation using aggregation in
relational database. Indian Journal of Science and Technology, 7, 44-46.
[34] Karthik, B., Kiran Kumar, T.V.U., Vijayaragavan, P., & Bharath Kumaran, E. (2013). Design of a digital
PLL using 0.35 μm CMOS technology. Middle-East Journal of Scientific Research, 18(12), 1803-1806.
[35] Sudhakara, P., Jagadeesh, D., Wang, Y., Prasad, C.V., Devi, A.K., Balakrishnan, G., Kim B.S., & Song, J.I.
(2013). Fabrication of Borassus fruit lignocellulose fiber/PP composites and comparison with jute, sisal and
coir fibers. Carbohydrate polymers, 98(1), 1002-1010.
[36] Kanniga, E., & Sundararajan, M. (2011). Modelling and characterization of DCO using pass transistors.
In Future Intelligent Information Systems, 86(1), 451-457. Springer, Berlin, Heidelberg
[37] Sachithanandam, P., Meikandaan, T.P., & Srividya, T. Steel framed multi storey residential building
analysis and design. International Journal of Applied Engineering Research, 9(22), 5527-5529.
[38] Kaliyamurthie, K.P., Udayakumar, R., Parameswari, D., & Mugunthan, S.N. (2013). Highly secured online
voting system over network. Indian Journal of Science and Technology, 6(S6), 4831-4836.
[39] Sathyaseelan, B., Manikandan, E., Lakshmanan, V., Baskaran, I., Sivakumar, K., Ladchumananandasivam,
R., Kennedy, J., & Maaza, M. (2016). Structural, optical and morphological properties of post-growth
calcined TiO2 nanopowder for opto-electronic device application: Ex-situ studies. Journal of Alloys and
Compounds, 671, 486-492.
[40] Saravanan, T., Sundar Raj M., & Gopalakrishnan K. (2014). SMES technology, SMES and facts system,
applications, advantages and technical limitations. Middle - East Journal of Scientific Research, 20(11),
1353-1358.
[41] Sofiazizi, A., & Kianfar, F. (2015). Modeling and Forecasting Exchange Rates Using Econometric Models
and Neural Networks. International Academic Journal of Innovative Research, 2(4), 11-27.
[42] Singh, S.P. (2014). Security Configuration and Performance Analysis of FTP Server. International Journal
of Communication and Computer Technologies, 2(2), 106-109.
[43] Bindu, M.V. (2018). Enhancement of Thermal Performance of Solar Parabolic Trough ConcentratorTechniques- Review. Bonfring International Journal of Industrial Engineering and Management Science,
9(3), 16-20.
[44] Nandhini, P., Vijayasharathy, G., Kokila, N.S., Kousalya, S., & Kousika, T. (2016). An Improved Approach
of DWT and ANC Algorithm for Removal of ECG Artifacts. International Journal of Communication and
Computer Technologies, 4(2), 82-87.
[45] Devi, G. (2016). High Speed Image Searching for Human Gait Feature Selection. International Journal of
Communication and Computer Technologies, 4(2), 88-95.
[46] Suba, R. And Satheeskumar, R. (2016). Efficient Cluster Based Congestion Control in Wireless Mesh
Network. International Journal of Communication and Computer Technologies, 4(2), 96-101.
[47] Amiri, M., & Akkasi, A. (2015). Assessing security challenges in online social networks. International
Academic Journal of Science and Engineering, 2(4), 1-10.
[48] Loganya, R., Lavanya, S., Logasangeerani, S., & Thiruveni, M. (2014). Low Power VLSI Architecture
forReconfigurable FIR Filter. International Journal of System Design and Information Processing, 2(2), 30-
33.
[49] Kiruthika, S., Dhivya, T., & Kiruthika, S.S. (2018). Performance Analysis of Faculty and Students Using
Neo 4j. Bonfring International Journal of Networking Technologies and Applications, 5(1), 3-5.
[50] KuthsiyatJahan, S., Chandru, K., Dhanapriyan, B., Kishore Kumar, R., and Vinothraj, G. (2017). SEPIC
Converter based Water Driven Pumping System by Using BLDC Motor. Bonfring International Journal of
Power Systems and Integrated Circuits, 7(1), 7-12
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Author
This work is licensed under a Creative Commons Attribution 4.0 International License.
You are free to:
- Share — copy and redistribute the material in any medium or format for any purpose, even commercially.
- Adapt — remix, transform, and build upon the material for any purpose, even commercially.
- The licensor cannot revoke these freedoms as long as you follow the license terms.
Under the following terms:
- Attribution — You must give appropriate credit , provide a link to the license, and indicate if changes were made . You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
- No additional restrictions — You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
Notices:
You do not have to comply with the license for elements of the material in the public domain or where your use is permitted by an applicable exception or limitation .
No warranties are given. The license may not give you all of the permissions necessary for your intended use. For example, other rights such as publicity, privacy, or moral rights may limit how you use the material.
