Design and Analysis of Propeller Shaft
DOI:
https://doi.org/10.61841/agqyc144Keywords:
Propeller Shaft, Design and Analysis, Composite Materials, E-glass/ Epoxy.Abstract
Substituting composite structures for conventional metallic structures has many advantages because of higher specific stiffness and strength of composite materials. This work deals with the replacement of conventional two-piece steel drive shafts with a single-piece e-glass/ epoxy, high strength carbon/epoxy and high modulus carbon/epoxy composite drive shaft for an automotive application. The design parameters were optimized with the objective of minimizing the weight of composite drive shaft. The design optimization also showed significant potential improvement in the performance of drive shaft. The main concept of our project is to reduce the weight of automotive drive shaft with the utilization of composite material. Composite materials have been used in automotive components because of their properties such as low weight, high specific stiffness, corrosion free, ability to produce complex shapes, high specific strength and high impact energy absorption etc .As the automotive drive shaft is a very important component of vehicle. The modeling of the drive shaft assembly was done using SOLIDWORKS software. A shaft has to be designed to meet the stringent design requirements for automotives. In automobiles the drive shaft is used for the transmission of motion from the engine to the differential. An automotive propeller shaft, or drive shaft, transmits power from the engine to differential gears of rear wheel-driving vehicle. In present work an attempt has been to estimate deflection, stresses under subjected loads & natural frequencies using Ansys software.
Downloads
References
[1] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Virtual instrumentation based process of
agriculture by automation. Middle-East Journal of Scientific Research, 20(12): 2604-2612.
[2] Udayakumar, R., Kaliyamurthie, K.P., & Khanaa, T.K. (2014). Data mining a boon: Predictive system for
university topper women in academia. World Applied Sciences Journal, 29(14): 86-90.
[3] Anbuselvi, S., Rebecca, L.J., Kumar, M.S., & Senthilvelan, T. (2012). GC-MS study of phytochemicals in
black gram using two different organic manures. J Chem Pharm Res., 4, 1246-1250
[4] Subramanian, A.P., Jaganathan, S.K., Manikandan, A., Pandiaraj, K.N., Gomathi, N., & Supriyanto, E.
(2016). Recent trends in nano-based drug delivery systems for efficient delivery of phytochemicals in
chemotherapy. RSC Advances, 6(54), 48294-48314.
[5] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Partial encryption and partial inference control
based disclosure in effective cost cloud. Middle-East Journal of Scientific Research, 20(12), 2456-2459.
[6] Lingeswaran, K., Prasad Karamcheti, S.S., Gopikrishnan, M., & Ramu, G. (2014). Preparation and
characterization of chemical bath deposited cds thin film for solar cell. Middle-East Journal of Scientific
Research, 20(7), 812-814.
[7] Maruthamani, D., Vadivel, S., Kumaravel, M., Saravanakumar, B., Paul, B., Dhar, S.S., Manikandan, A., &
Ramadoss, G. (2017). Fine cutting edge shaped Bi2O3rods/reduced graphene oxide (RGO) composite for
supercapacitor and visible-light photocatalytic applications. Journal of colloid and interface science, 498,
449-459.
[8] Gopalakrishnan, K., Sundeep Aanand, J., & Udayakumar, R. (2014). Electrical properties of doped
azopolyester. Middle-East Journal of Scientific Research, 20(11). 1402-1412.
[9] Subhashree, A.R., Parameaswari, P.J., Shanthi, B., Revathy, C., & Parijatham, B.O. (2012). The reference
intervals for the haematological parameters in healthy adult population of chennai, southern India. Journal
of Clinical and Diagnostic Research: JCDR, 6(10), 1675-1680.
[10] Niranjan, U., Subramanyam, R.B.V., & Khanaa, V. (2010, September). Developing a web recommendation
system based on closed sequential patterns. In International Conference on Advances in Information and
Communication Technologies, 101, 171-179. Springer, Berlin, Heidelberg.
[11] Slimani, Y., Baykal, A., & Manikandan, A. (2018). Effect of Cr3+ substitution on AC susceptibility of Ba
hexaferrite nanoparticles. Journal of Magnetism and Magnetic Materials, 458, 204-212.
[12] Premkumar, S., Ramu, G., Gunasekaran, S., & Baskar, D. (2014). Solar industrial process heating associated
with thermal energy storage for feed water heating. Middle East Journal of Scientific Research, 20(11),
1686-1688.
[13] Kumar, S.S., Karrunakaran, C.M., Rao, M.R.K., & Balasubramanian, M.P. (2011). Inhibitory effects of
Indigofera aspalathoides on 20-methylcholanthrene-induced chemical carcinogenesis in rats. Journal of
carcinogenesis, 10.
[14] Beula Devamalar, P.M., Thulasi Bai, V., & Srivatsa, S.K. (2009). Design and architecture of real time webcentric tele health diabetes diagnosis expert system. International Journal of Medical Engineering and
Informatics, 1(3), 307-317.
[15] Ravichandran, A.T., Srinivas, J., Karthick, R., Manikandan, A., & Baykal, A. (2018). Facile combustion
synthesis, structural, morphological, optical and antibacterial studies of Bi1− xAlxFeO3 (0.0≤ x≤ 0.15)
nanoparticles. Ceramics International, 44(11), 13247-13252.
[16] Thovhogi, N., Park, E., Manikandan, E., Maaza, M., & Gurib-Fakim, A. (2016). Physical properties of CdO
nanoparticles synthesized by green chemistry via Hibiscus Sabdariffa flower extract. Journal of Alloys and
Compounds, 655, 314-320.
[17] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2014). Wide area wireless networks-IETF. Middle-East
Journal of Scientific Research, 20(12), 2042-2046.
[18] Sundar Raj, M., Saravanan, T., & Srinivasan, V. (2014). Design of silicon-carbide based cascaded
multilevel inverter. Middle-East Journal of Scientific Research, 20(12), 1785- 1791.
[19] Achudhan, M., Jayakumar M.P. (2014). Mathematical modeling and control of an electrically-heated
catalyst. International Journal of Applied Engineering Research, 9(23), 23013.
[20] Thooyamani, K.P., Khanaa, V., & Udayakumar, R. (2013). Application of pattern recognition for farsi
license plate recognition. Middle-East Journal of Scientific Research, 18(12), 1768-1774.
[21] Jebaraj, S., Iniyan S. (2006). Renewable energy programmes in India. International Journal of Global
Energy Issues, 26(43528), 232-257.
[22] Sharmila, S., & Jeyanthi Rebecca, L. (2013). Md Saduzzaman., Biodegradation of domestic effluent using
different solvent extracts of Murraya koenigii. J Chem and Pharm Res, 5(2), 279-282.
[23] Asiri, S., Sertkol, M., Guner, S., Gungunes, H., Batoo, K.M., Saleh, T.A., Manikandan A., & Baykal, A.
(2018). Hydrothermal synthesis of CoyZnyMn1-2yFe2O4 nanoferrites: magneto-optical
investigation. Ceramics International, 44(5), 5751-5759.
[24] Rani, A.J., & Mythili, S.V. (2014). Study on total antioxidant status in relation to oxidative stress in type 2
diabetes mellitus. Journal of clinical and diagnostic research: JCDR, 8(3), 108-110.
[25] Karthik, B. (2014). Arulselvi, Noise removal using mixtures of projected gaussian scale mixtures. MiddleEast Journal of Scientific Research, 20(12), 2335-2340.
[26] Karthik, B., Arulselvi, & Selvaraj, A. (2014). Test data compression architecture for low power VLSI
testing. Middle - East Journal of Scientific Research, 20(12), 2331-2334.
[27] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). Privacy conscious screening framework
for frequently moving objects. Middle-East Journal of Scientific Research, 20(8), 1000-1005.
[28] Kaliyamurthie, K.P., Parameswari, D., & Udayakumar, R. (2013). QOS aware privacy preserving location
monitoring in wireless sensor network. Indian Journal of Science and Technology, 6(5), 4648-4652.
[29] Silambarasu, A., Manikandan, A., & Balakrishnan, K. (2017). Room-temperature superparamagnetism and
enhanced photocatalytic activity of magnetically reusable spinel ZnFe 2 O 4 nanocatalysts. Journal of
Superconductivity and Novel Magnetism, 30(9), 2631-2640.
[30] Jasmin, M., Vigneshwaran, T., & Beulah Hemalatha, S. (2015). Design of power aware on chip embedded
memory based FSM encoding in FPGA. International Journal of Applied Engineering Research, 10(2),
4487-4496.
[31] Philomina, S., & Karthik, B. (2014). Wi-Fi energy meter implementation using embedded linux in ARM
9. Middle-East Journal of Scientific Research, 20, 2434-2438.
[32] Vijayaragavan, S.P., Karthik, B., & Kiran Kumar, T.V.U. (2014). A DFIG based wind generation system
with unbalanced stator and grid condition. Middle-East Journal of Scientific Research, 20(8), 913-917.
[33] Rajakumari, S.B., & Nalini, C. (2014). An efficient data mining dataset preparation using aggregation in
relational database. Indian Journal of Science and Technology, 7, 44-46.
[34] Karthik, B., Kiran Kumar, T.V.U., Vijayaragavan, P., & Bharath Kumaran, E. (2013). Design of a digital
PLL using 0.35 μm CMOS technology. Middle-East Journal of Scientific Research, 18(12), 1803-1806.
[35] Sudhakara, P., Jagadeesh, D., Wang, Y., Prasad, C.V., Devi, A.K., Balakrishnan, G., Kim B.S., & Song, J.I.
(2013). Fabrication of Borassus fruit lignocellulose fiber/PP composites and comparison with jute, sisal and
coir fibers. Carbohydrate polymers, 98(1), 1002-1010.
[36] Kanniga, E., & Sundararajan, M. (2011). Modelling and characterization of DCO using pass transistors.
In Future Intelligent Information Systems, 86(1), 451-457. Springer, Berlin, Heidelberg.
[37] Sachithanandam, P., Meikandaan, T.P., & Srividya, T. Steel framed multi storey residential building
analysis and design. International Journal of Applied Engineering Research, 9(22), 5527-5529.
[38] Kaliyamurthie, K.P., Udayakumar, R., Parameswari, D., & Mugunthan, S.N. (2013). Highly secured online
voting system over network. Indian Journal of Science and Technology, 6(S6), 4831-4836.
[39] Sathyaseelan, B., Manikandan, E., Lakshmanan, V., Baskaran, I., Sivakumar, K., Ladchumananandasivam,
R., Kennedy, J., & Maaza, M. (2016). Structural, optical and morphological properties of post-growth
calcined TiO2 nanopowder for opto-electronic device application: Ex-situ studies. Journal of Alloys and
Compounds, 671, 486-492.
[40] Saravanan, T., Sundar Raj M., & Gopalakrishnan K. (2014). SMES technology, SMES and facts system,
applications, advantages and technical limitations. Middle - East Journal of Scientific Research, 20(11),
1353-1358.
[41] Dr.AntoBennet, M., Karthika, S., Durga Devi, A., Lakshmisree, B., & Thilagavathi, S.(2016).
Implementation of Portable Fetal and Maternal Heart Rate Recorder by Using RISC Microcontroller. Excel
International Journal of Technology, Engineering and Management, 3(2), 58-61.
[42] Gokila, L., Poongodi, V., and Dr.Thangadurai, K. (2016). Multi Scheduling Reactive Resource Sharing for
Dynamic Dataflow in Cloud Environment. Bonfring International Journal of Data Mining, 6(4), 46-52.
doi:10.9756/BIJDM.8307
[43] Orhorhoro, E.K., Orhorhoro, O.W., & Ogini, M.E. (2016). Assembly and Investigation of Solar Powered
Air Conditioner for Household Use in Nigeria. International Academic Journal of Innovative Research,
3(10), 84-99.
[44] Prabha, I.M.T., & Gayathri, R. (2014). Isolation Enhancement in Microstrip Antenna Arrays. International
Journal of Communication and Computer Technologies, 2(2), 79-84.
[45] Jamuna, K., Jayapriya, G., & Jayanthi, K. (2014). Mems Based Haptic Assistive System for Physical
Impairments. International Journal of Communication and Computer Technologies, 2(2), 88-93.
[46] Bourvil, & Levi. (2017). Multi-Level Trust Privacy Preserving Data Mining to Enhance Data Security and
Prevent Leakage of the Sensitive Data. Bonfring International Journal of Industrial Engineering and
Management Science, 7(2), 21-25.
[47] Mozaffari, M., Pourbahram, A., & Marzdashti, A.F. (2015). Knowing Effective Factors in Reducing Power
Consumption in MAC Protocols’ Listening For Wireless Sensor Networks. International Academic Journal
of Science and Engineering, 2(5), 14-21.
[48] Youzband, R.S., & Mirnia, M.K. (2015). Designing Reverse Converter for the New Three-Moduli Set
{2^(2n+1), 2^n-1, 2^n+1}. International Academic Journal of Science and Engineering, 2(5), 32-38.
[49] Rajalakshmi, M., & Subadra, S. (2014). Smile Emotional Identification for Negative Emotions Detection by
Fuzzy Neural Network with Pixel Differences. International Journal of System Design and Information
Processing, 2(4), 59-65.
[50] Gopalakrishnan, C., & Iyapparaja, M. (2018). Tagging in IoT Category based Applications Using Vitality
Proficient Geospatial Technique. Bonfring International Journal of Networking Technologies and
Applications, 5(2), 1-5.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Author
This work is licensed under a Creative Commons Attribution 4.0 International License.
You are free to:
- Share — copy and redistribute the material in any medium or format for any purpose, even commercially.
- Adapt — remix, transform, and build upon the material for any purpose, even commercially.
- The licensor cannot revoke these freedoms as long as you follow the license terms.
Under the following terms:
- Attribution — You must give appropriate credit , provide a link to the license, and indicate if changes were made . You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
- No additional restrictions — You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits.
Notices:
You do not have to comply with the license for elements of the material in the public domain or where your use is permitted by an applicable exception or limitation .
No warranties are given. The license may not give you all of the permissions necessary for your intended use. For example, other rights such as publicity, privacy, or moral rights may limit how you use the material.
